液位变送器_西北地区使用的投入式液位变送器特点

作为西北地区的液位变送器生产厂家,西安液位变送器的厂家,是西北地区少数的可以同时生产压力/差压液位变送器的电路板.金属电容传感器/扩散硅原理传感器的厂家.依托雄厚的原西安仪表厂家的生产工艺和技术.完全能够为西北的新疆投入式液位变送器厂家.青海的投入式液位变送器使用厂家,宁夏投入式液位变送器使用厂家,甘肃液位变送器厂家独立设计,提供产品高效优质,性能稳定,测量精度高,价格适中的巨大优势.

西北地区使用的投入式液位变送器特点是一种能就地显示或带远传与控制的液位计。它广泛用于石油、化工、轻工、油罐，电力、核工业以及食品等工业中，对各种塔、罐、槽、箱等容器中介质的液位进行指示和控制。作为西安华恒仪表生产厂家,在西北复杂的工况使用的时候需要注意

.
        西北地区使用的投入式液位变送器特点产
        1、稳定性好，精度高
        2、直接投入到被测介质中，安装使用相当方便。
        3、固态结构，无可动部件，高可靠性，使用寿命长从水、油到粘度较大的糊状都可以进行高精度测量，
        4、不受被测介质起泡、沉积、电气特性的影响
        5、宽范围的温度补偿。
        6、具有电源反相极性保护及过载限流保护。
        7、缆式液位变送器的压力探头为不锈钢（1Cr18Ni9Ti）材料，电缆护套为橡塑，特殊要求可选择聚四氟乙烯探头、不锈钢或聚四氟乙烯电缆护套材料。
        8、直杆式液位变送器的压力探头及电缆护套为全不锈钢（1Cr18Ni9Ti）材料，变送器的插入深度可在±20cm范围内自由调整。
        西北地区使用的投入式液位变送器特点/ 安装指南
        1、由于罐底或舱底易沉积污泥、油渣等物，建议将测量探头离开罐（舱）底一定高度，以免杂物堵塞探头。
        2、在介质波动较大，导气电缆很长的情况下，对探头应采用套筒将其固定，以防探头摆动而影响测量精度。
        3、变送器侧面安装时，导气电缆弯曲半径应大于10厘米，避免弯曲过度而将导气电缆损坏。
        4、投入式液位变送器接地端子应可靠接地，电源屏蔽线应与其相连。
        5、测量易爆危险品时，必须严格按照GB3836.1-83《爆炸性环境用防爆电器设备通用要求》和GB3836.4-83《本质安全型电路和电气设备“i”》中的有关规定进行安装。
        在拥有核心的电路板和压力/差压传感器自主研发的基础上 生产的投入式液位表送器拥有,高精度测量，不受被测介质起泡、沉积、电气特性的影响宽范围的温度补偿 ,固态结构，无可动部件，高可靠性，使用寿命长，从水、油到粘度较大的糊状都可以进行 ,稳定性好，精度高，可在高温环境下工作 ,直接投入到拥有被测介质中，安装使用相当方便.等巨大优势/液位变送器_西北地区使用的投入式液位变送器特点

As a level transmitter manufacturer in Northwest China, Xi'an level transmitter manufacturer, It is one of the few manufacturers in Northwest China that can produce pressure / differential pressure liquid level transmitter circuit board, metal capacitance sensor / diffusion silicon principle sensor at the same time. Relying on the strong production technology and technology of original Xi'an instrument manufacturer, it can be fully used by Xinjiang input liquid level transmitter manufacturer in Northwest China and Qinghai input liquid level transmitter manufacturer, Ningxia input type liquid level transmitter manufacturer and Gansu liquid level transmitter manufacturer independently design, providing the huge advantages of high efficiency, high quality, stable performance, high measurement accuracy and moderate price

The input type liquid level transmitter used in Northwest China is characterized by a liquid level meter which can be displayed locally or with remote transmission and control. It is widely used in petroleum, chemical, light industry, oil tank, electric power, nuclear industry, food and other industries to indicate and control the liquid level of the medium in various columns, tanks, tanks and other containers. As an instrument manufacturer of Xi'an Huaheng, we need to pay attention to the complex working conditions in Northwest China

3151 input liquid level transmitter_ High static pressure level transmitter_ Silicon principle static pressure transmitter
Characteristics of input liquid level transmitter used in Northwest China
1. Good stability and accuracy
2. It can be directly put into the tested medium, which is quite convenient to install and use.
3. Solid structure, no movable parts, high reliability, long service life, from water and oil to paste with high viscosity, can be measured with high precision,
4. Not affected by the foaming, deposition and electrical characteristics of the measured medium
5. Wide range temperature compensation.
6. It has reverse polarity protection and overload current limiting protection.
7. The pressure probe of cable type liquid level transmitter is made of stainless steel (1Cr18Ni9Ti), and the cable sheath is made of rubber and plastic. For special requirements, PTFE probe, stainless steel or PTFE cable sheath material can be selected.
8. The pressure probe and cable sheath of the straight rod liquid level transmitter are made of all stainless steel (1Cr18Ni9Ti), and the insertion depth of the transmitter can be freely adjusted within ± 20cm.
Characteristics / installation guide of input liquid level transmitter used in Northwest China
1. As sludge and oil residue are easy to deposit at the bottom of tank or bilge, it is recommended to leave the measuring probe at a certain height from the tank (bilge) bottom to prevent the probe from being blocked by sundries.
2. In the case of large medium fluctuation and long air conducting cable, the probe should be fixed by sleeve to prevent the probe from swinging and affecting the measurement accuracy.
3. When the transmitter is installed at the side, the bending radius of the air conducting cable shall be greater than 10cm to avoid damage of the air conducting cable due to excessive bending.
4. The grounding terminal of the input liquid level transmitter shall be reliably grounded, and the power shield wire shall be connected with it.
5. When measuring explosive dangerous goods, it must be installed in strict accordance with the relevant provisions of gb3836.1-83 General requirements for explosion proof electrical equipment for explosive atmospheres and gb3836.4-83 "intrinsically safe circuit and electrical equipment" I ".
Based on the independent research and development of the core circuit board and pressure / differential pressure sensor, the input type liquid level meter transmitter has high-precision measurement, wide range temperature compensation free from the influence of the foaming, deposition and electrical characteristics of the measured medium, solid structure, no movable parts, high reliability, long service life, and can be carried out from water, oil to paste with large viscosity, With good stability and high precision, it can work in high temperature environment and be directly put into the medium under test. It is quite convenient to install and use_ Characteristics of input liquid level transmitter used in Northwest China